[ 0.000000] Linux version 5.10.103 (labby@lobon) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19053+1-921392e216) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 Sun Mar 6 19:14:20 2022 [ 0.000000] RTL838X model is 83826800 [ 0.000000] SoC Type: RTL8382 [ 0.000000] Kernel command line: console=ttyS0,115200 mem=64M quiet [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019070 (MIPS 4KEc) [ 0.000000] MIPS: machine is ZyXEL GS1900-24HP v1 [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Using appended Device Tree. [ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes. [ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] Normal zone: 144 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16384 pages, LIFO batch:3 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping off. Total pages: 16240 [ 0.000000] Kernel command line: console=ttyS0,115200 [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 55980K/65536K available (5609K kernel code, 613K rwdata, 1212K rodata, 1196K init, 203K bss, 9556K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] random: get_random_bytes called from start_kernel+0x31c/0x50c with crng_init=0 [ 0.000000] CPU frequency from device tree: 500MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns [ 0.000018] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns [ 0.008690] Calibrating delay loop... 498.89 BogoMIPS (lpj=2494464) [ 0.075561] pid_max: default: 32768 minimum: 301 [ 0.081055] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.089107] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.103303] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.119589] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.130505] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.138201] pinctrl core: initialized pinctrl subsystem [ 0.145361] NET: Registered protocol family 16 [ 0.315951] clocksource: Switched to clocksource MIPS [ 0.324302] NET: Registered protocol family 2 [ 0.329669] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.339011] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.348472] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.357045] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.364807] TCP: Hash tables configured (established 1024 bind 1024) [ 0.372454] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.379845] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.388106] NET: Registered protocol family 1 [ 0.413225] workingset: timestamp_bits=14 max_order=14 bucket_order=0 [ 0.429268] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.435654] jffs2: version 2.2 (NAND) (SUMMARY) (ZLIB) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.451707] pinctrl-single 1b001000.pinmux: 32 pins, size 4 [ 0.458635] pinctrl-single 1b00a000.pinmux: 32 pins, size 4 [ 0.465639] realtek_gpio_probe probing RTL GPIO [ 0.472028] Probing RTL8231 GPIOs [ 0.475642] rtl8231_init called, MDIO bus ID: 0 [ 0.480994] gpio-464 (poe_enable): hogged as output/high [ 0.589518] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.598804] printk: console [ttyS0] disabled [ 0.603597] 18002000.uart: ttyS0 at MMIO 0x18002000 (irq = 31, base_baud = 12500000) is a 16550A [ 0.613428] printk: console [ttyS0] enabled [ 0.622776] printk: bootconsole [early0] disabled [ 0.634852] 18002100.uart: ttyS1 at MMIO 0x18002100 (irq = 30, base_baud = 12500000) is a 16550A [ 1.320129] brd: module loaded [ 1.333179] spi-nor spi0.0: mx25l12805d (16384 Kbytes) [ 1.339213] 7 fixed-partitions partitions found on MTD device spi0.0 [ 1.346483] Creating 7 MTD partitions on "spi0.0": [ 1.351869] 0x000000000000-0x000000040000 : "u-boot" [ 1.363261] 0x000000040000-0x000000050000 : "u-boot-env" [ 1.371961] 0x000000050000-0x000000060000 : "u-boot-env2" [ 1.385399] 0x000000060000-0x000000160000 : "jffs" [ 1.393423] 0x000000160000-0x000000260000 : "jffs2" [ 1.406369] 0x000000260000-0x000000930000 : "firmware" [ 1.415011] 2 uimage-fw partitions found on MTD device firmware [ 1.421809] Creating 2 MTD partitions on "firmware": [ 1.427499] 0x000000000000-0x000000320000 : "kernel" [ 1.440329] 0x000000320000-0x0000006d0000 : "rootfs" [ 1.448499] mtd: device 7 (rootfs) set to be root filesystem [ 1.457518] 1 squashfs-split partitions found on MTD device rootfs [ 1.464474] 0x000000520000-0x0000006d0000 : "rootfs_data" [ 1.473146] 0x000000930000-0x000001000000 : "runtime2" [ 1.505396] Probing RTL838X eth device pdev: 82098c00, dev: 82098c10 [ 1.563061] Found SoC ID: 8382: RTL8382, family 8380 [ 1.568852] rtl8380_init_mac [ 1.572129] Using MAC 000004bf6d22f5f8 [ 1.668273] Realtek RTL8218B (internal) mdio-bus:08: Detected internal RTL8218B [ 1.676620] Firmware loaded. Size 1184, magic: 83808380 [ 2.585964] random: fast init done [ 4.216430] Phy on MAC 0: 1cc981 [ 4.230307] Realtek RTL8218B (external) mdio-bus:00: Detected external RTL8218B [ 4.238607] Firmware loaded. Size 1168, magic: 83808380 [ 4.386212] Realtek RTL8218B (external) mdio-bus:00: Detected chip revision 0002 [ 5.661243] mdio_bus mdio-bus: MDIO device at address 24 is missing. [ 5.668671] mdio_bus mdio-bus: MDIO device at address 26 is missing. [ 5.677759] i2c /dev entries driver [ 5.686188] NET: Registered protocol family 10 [ 5.715670] Segment Routing with IPv6 [ 5.720154] NET: Registered protocol family 17 [ 5.726079] 8021q: 802.1Q VLAN Support v1.8 [ 5.731959] i2c-gpio i2c-gpio-0: Slow GPIO pins might wreak havoc into I2C/SMBus bus timing [ 5.741970] i2c-gpio i2c-gpio-0: using lines 475 (SDA) and 476 (SCL) [ 5.749856] i2c-gpio i2c-gpio-1: Slow GPIO pins might wreak havoc into I2C/SMBus bus timing [ 5.759813] i2c-gpio i2c-gpio-1: using lines 481 (SDA) and 482 (SCL) [ 5.768838] sfp sfp-p25: Host maximum power 1.0W [ 5.775883] sfp sfp-p26: Host maximum power 1.0W [ 5.803564] Phy on MAC 0: 1cc981 [ 5.817542] Realtek RTL8218B (external) rtl838x slave mii-0:00: Detected external RTL8218B [ 5.826907] Firmware loaded. Size 1168, magic: 83808380 [ 5.976213] Realtek RTL8218B (external) rtl838x slave mii-0:00: Detected chip revision 0002 [ 7.228770] Realtek RTL8218B (internal) rtl838x slave mii-0:08: Detected internal RTL8218B [ 7.238146] Firmware loaded. Size 1184, magic: 83808380 [ 9.812464] rtl83xx_mdio_probe found port 8 [ 9.817325] rtl83xx_mdio_probe port 8 has phandle [ 9.822592] rtl83xx_mdio_probe port -1 has SDS [ 9.827669] rtl83xx_mdio_probe found port 9 [ 9.832356] rtl83xx_mdio_probe port 9 has phandle [ 9.837711] rtl83xx_mdio_probe port -1 has SDS [ 9.842695] rtl83xx_mdio_probe found port 10 [ 9.847605] rtl83xx_mdio_probe port 10 has phandle [ 9.852968] rtl83xx_mdio_probe port -1 has SDS [ 9.858047] rtl83xx_mdio_probe found port 11 [ 9.862831] rtl83xx_mdio_probe port 11 has phandle [ 9.868283] rtl83xx_mdio_probe port -1 has SDS [ 9.873267] rtl83xx_mdio_probe found port 12 [ 9.878143] rtl83xx_mdio_probe port 12 has phandle [ 9.883506] rtl83xx_mdio_probe port -1 has SDS [ 9.888579] rtl83xx_mdio_probe found port 13 [ 9.893367] rtl83xx_mdio_probe port 13 has phandle [ 9.898820] rtl83xx_mdio_probe port -1 has SDS [ 9.903812] rtl83xx_mdio_probe found port 14 [ 9.908687] rtl83xx_mdio_probe port 14 has phandle [ 9.914050] rtl83xx_mdio_probe port -1 has SDS [ 9.919122] rtl83xx_mdio_probe found port 15 [ 9.923911] rtl83xx_mdio_probe port 15 has phandle [ 9.929364] rtl83xx_mdio_probe port -1 has SDS [ 9.934347] rtl83xx_mdio_probe found port 28 [ 9.939226] rtl83xx_mdio_probe found port 0 [ 9.943912] rtl83xx_mdio_probe port 0 has phandle [ 9.949268] rtl83xx_mdio_probe port -1 has SDS [ 9.954256] rtl83xx_mdio_probe found port 1 [ 9.959057] rtl83xx_mdio_probe port 1 has phandle [ 9.964323] rtl83xx_mdio_probe port -1 has SDS [ 9.969403] rtl83xx_mdio_probe found port 2 [ 9.974088] rtl83xx_mdio_probe port 2 has phandle [ 9.979445] rtl83xx_mdio_probe port -1 has SDS [ 9.984431] rtl83xx_mdio_probe found port 3 [ 9.989209] rtl83xx_mdio_probe port 3 has phandle [ 9.994472] rtl83xx_mdio_probe port -1 has SDS [ 9.999548] rtl83xx_mdio_probe found port 4 [ 10.004239] rtl83xx_mdio_probe port 4 has phandle [ 10.009595] rtl83xx_mdio_probe port -1 has SDS [ 10.014589] rtl83xx_mdio_probe found port 5 [ 10.019366] rtl83xx_mdio_probe port 5 has phandle [ 10.024631] rtl83xx_mdio_probe port -1 has SDS [ 10.029713] rtl83xx_mdio_probe found port 6 [ 10.034404] rtl83xx_mdio_probe port 6 has phandle [ 10.039761] rtl83xx_mdio_probe port -1 has SDS [ 10.044755] rtl83xx_mdio_probe found port 7 [ 10.049533] rtl83xx_mdio_probe port 7 has phandle [ 10.054797] rtl83xx_mdio_probe port -1 has SDS [ 10.059872] rtl83xx_mdio_probe found port 16 [ 10.064658] rtl83xx_mdio_probe port 16 has phandle [ 10.070136] rtl83xx_mdio_probe port -1 has SDS [ 10.075123] rtl83xx_mdio_probe found port 17 [ 10.080000] rtl83xx_mdio_probe port 17 has phandle [ 10.085359] rtl83xx_mdio_probe port -1 has SDS [ 10.090434] rtl83xx_mdio_probe found port 18 [ 10.095221] rtl83xx_mdio_probe port 18 has phandle [ 10.100674] rtl83xx_mdio_probe port -1 has SDS [ 10.105667] rtl83xx_mdio_probe found port 19 [ 10.110542] rtl83xx_mdio_probe port 19 has phandle [ 10.115904] rtl83xx_mdio_probe port -1 has SDS [ 10.120996] rtl83xx_mdio_probe found port 20 [ 10.125764] rtl83xx_mdio_probe port 20 has phandle [ 10.131219] rtl83xx_mdio_probe port -1 has SDS [ 10.136316] rtl83xx_mdio_probe found port 21 [ 10.141105] rtl83xx_mdio_probe port 21 has phandle [ 10.146560] rtl83xx_mdio_probe port -1 has SDS [ 10.151553] rtl83xx_mdio_probe found port 22 [ 10.156428] rtl83xx_mdio_probe port 22 has phandle [ 10.161789] rtl83xx_mdio_probe port -1 has SDS [ 10.166865] rtl83xx_mdio_probe found port 23 [ 10.171649] rtl83xx_mdio_probe port 23 has phandle [ 10.177127] rtl83xx_mdio_probe port -1 has SDS [ 10.182124] rtl83xx_mdio_probe found port 24 [ 10.187011] rtl83xx-switch switch@1b000000: Port node 24 misses phy-handle [ 10.194705] rtl83xx_mdio_probe found port 26 [ 10.199590] rtl83xx-switch switch@1b000000: Port node 26 misses phy-handle [ 10.211899] In rtl83xx_vlan_setup [ 10.215648] UNKNOWN_MC_PMASK: 000000001fffffff [ 10.220738] VLAN profile 0: L2 learning: 1, UNKN L2MC FLD PMSK 511, UNKN IPMC FLD PMSK 511, UNKN IPv6MC FLD PMSK: 511 [ 11.306110] rtl83xx_enable_phy_polling: ffffff [ 12.346508] rtl83xx-switch switch@1b000000 lan1 (uninitialized): PHY [mdio-bus:00] driver [Realtek RTL8218B (external)] (irq=POLL) [ 12.362183] rtl83xx-switch switch@1b000000 lan2 (uninitialized): PHY [mdio-bus:01] driver [Realtek RTL8218B (external)] (irq=POLL) [ 12.377851] rtl83xx-switch switch@1b000000 lan3 (uninitialized): PHY [mdio-bus:02] driver [Realtek RTL8218B (external)] (irq=POLL) [ 12.393656] rtl83xx-switch switch@1b000000 lan4 (uninitialized): PHY [mdio-bus:03] driver [Realtek RTL8218B (external)] (irq=POLL) [ 12.409201] rtl83xx-switch switch@1b000000 lan5 (uninitialized): PHY [mdio-bus:04] driver [Realtek RTL8218B (external)] (irq=POLL) [ 12.424903] rtl83xx-switch switch@1b000000 lan6 (uninitialized): PHY [mdio-bus:05] driver [Realtek RTL8218B (external)] (irq=POLL) [ 12.440879] rtl83xx-switch switch@1b000000 lan7 (uninitialized): PHY [mdio-bus:06] driver [Realtek RTL8218B (external)] (irq=POLL) [ 12.456680] rtl83xx-switch switch@1b000000 lan8 (uninitialized): PHY [mdio-bus:07] driver [Realtek RTL8218B (external)] (irq=POLL) [ 12.472356] rtl83xx-switch switch@1b000000 lan9 (uninitialized): PHY [mdio-bus:08] driver [Realtek RTL8218B (internal)] (irq=POLL) [ 12.498217] rtl83xx-switch switch@1b000000 lan10 (uninitialized): PHY [mdio-bus:09] driver [Realtek RTL8218B (internal)] (irq=POLL) [ 12.524103] rtl83xx-switch switch@1b000000 lan11 (uninitialized): PHY [mdio-bus:0a] driver [Realtek RTL8218B (internal)] (irq=POLL) [ 12.550586] rtl83xx-switch switch@1b000000 lan12 (uninitialized): PHY [mdio-bus:0b] driver [Realtek RTL8218B (internal)] (irq=POLL) [ 12.576668] rtl83xx-switch switch@1b000000 lan13 (uninitialized): PHY [mdio-bus:0c] driver [Realtek RTL8218B (internal)] (irq=POLL) [ 12.603073] rtl83xx-switch switch@1b000000 lan14 (uninitialized): PHY [mdio-bus:0d] driver [Realtek RTL8218B (internal)] (irq=POLL) [ 12.629234] rtl83xx-switch switch@1b000000 lan15 (uninitialized): PHY [mdio-bus:0e] driver [Realtek RTL8218B (internal)] (irq=POLL) [ 12.655119] rtl83xx-switch switch@1b000000 lan16 (uninitialized): PHY [mdio-bus:0f] driver [Realtek RTL8218B (internal)] (irq=POLL) [ 12.681293] rtl83xx-switch switch@1b000000 lan17 (uninitialized): PHY [mdio-bus:10] driver [REALTEK RTL8218D] (irq=POLL) [ 12.706034] rtl83xx-switch switch@1b000000 lan18 (uninitialized): PHY [mdio-bus:11] driver [REALTEK RTL8218D] (irq=POLL) [ 12.731023] rtl83xx-switch switch@1b000000 lan19 (uninitialized): PHY [mdio-bus:12] driver [REALTEK RTL8218D] (irq=POLL) [ 12.756478] rtl83xx-switch switch@1b000000 lan20 (uninitialized): PHY [mdio-bus:13] driver [REALTEK RTL8218D] (irq=POLL) [ 12.781586] rtl83xx-switch switch@1b000000 lan21 (uninitialized): PHY [mdio-bus:14] driver [REALTEK RTL8218D] (irq=POLL) [ 12.806501] rtl83xx-switch switch@1b000000 lan22 (uninitialized): PHY [mdio-bus:15] driver [REALTEK RTL8218D] (irq=POLL) [ 12.831551] rtl83xx-switch switch@1b000000 lan23 (uninitialized): PHY [mdio-bus:16] driver [REALTEK RTL8218D] (irq=POLL) [ 12.856664] rtl83xx-switch switch@1b000000 lan24 (uninitialized): PHY [mdio-bus:17] driver [REALTEK RTL8218D] (irq=POLL) [ 12.875315] rtl83xx-switch switch@1b000000: configuring for fixed/internal link mode [ 12.884840] DSA: tree 0 setup [ 12.888402] LINK state irq: 20 [ 12.891922] In rtl83xx_setup_qos [ 12.895539] Setting up RTL838X QoS [ 12.899450] RTL838X_PRI_SEL_TBL_CTRL(i): 00033112 [ 12.904710] Current Intprio2queue setting: 00000000 [ 12.910247] QM_PKT2CPU_INTPRI_MAP: 00fac688 [ 12.915093] rtl838x_dbgfs_init called [ 12.986387] rtl83xx-switch switch@1b000000: Link is Up - 1Gbps/Full - flow control off [ 12.995281] rtl83xx_fib_event_work_do: FIB4 default rule failed [ 13.012153] VFS: Mounted root (squashfs filesystem) readonly on device 31:7. [ 13.033818] Freeing unused kernel memory: 1196K [ 13.039051] This architecture does not have kernel memory protection. [ 13.046388] Run /sbin/init as init process [ 13.050973] with arguments: [ 13.054281] /sbin/init [ 13.057403] with environment: [ 13.060926] HOME=/ [ 13.063555] TERM=linux [ 13.889514] init: Console is alive [ 13.894282] init: - watchdog - [ 14.127294] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 14.242704] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 14.261913] init: - preinit - [ 15.821102] random: jshn: uninitialized urandom read (4 bytes read) [ 15.975350] random: jshn: uninitialized urandom read (4 bytes read) [ 17.636881] random: jshn: uninitialized urandom read (4 bytes read) [ 17.741592] random: jshn: uninitialized urandom read (4 bytes read) [ 18.125827] random: jshn: uninitialized urandom read (4 bytes read) [ 18.903899] RESETTING 8380, CPU_PORT 28 [ 19.108906] rtl838x-eth 1b00a300.ethernet eth0: configuring for fixed/internal link mode [ 19.117975] In rtl838x_mac_config, mode 1 [ 19.126626] rtl83xx-switch switch@1b000000 lan1: configuring for phy/qsgmii link mode [ 19.135770] 8021q: adding VLAN 0 to HW filter on device lan1 [ 19.142836] In rtl838x_mac_config, mode 1 [ 19.147503] rtl838x-eth 1b00a300.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 19.196114] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 19.203256] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 19.210962] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 19.346214] rtl83xx_fib_event_work_do: FIB4 failed [ 19.351607] rtl83xx_fib_event_work_do: FIB4 failed [ 19.366229] rtl83xx_fib_event_work_do: FIB4 failed [ 19.371620] rtl83xx_fib_event_work_do: FIB4 failed [ 19.463979] random: procd: uninitialized urandom read (4 bytes read) [ 21.306071] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 23.933918] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000 [ 23.942132] jffs2_build_filesystem(): unlocking the mtd device... [ 23.942265] done. [ 23.951434] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 30.866274] done. [ 30.876942] jffs2: notice: (1315) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 30.897806] mount_root: overlay filesystem has not been fully initialized yet [ 30.911019] mount_root: switching to jffs2 overlay [ 30.923159] overlayfs: upper fs does not support tmpfile. [ 31.709412] urandom-seed: Seed file not found (/etc/urandom.seed) [ 31.957367] rtl83xx_fib4_del: no such gateway: 0.0.0.0 [ 31.963149] rtl83xx_fib4_del: no such gateway: 0.0.0.0 [ 31.986112] rtl83xx_fib4_del: no such gateway: 0.0.0.0 [ 31.991898] rtl83xx_fib4_del: no such gateway: 0.0.0.0 [ 32.034781] procd: - early - [ 32.038906] procd: - watchdog - [ 34.752704] procd: - watchdog - [ 34.757693] procd: - ubus - [ 34.883111] random: ubusd: uninitialized urandom read (4 bytes read) [ 34.893739] random: ubusd: uninitialized urandom read (4 bytes read) [ 34.902128] random: ubusd: uninitialized urandom read (4 bytes read) [ 34.919704] procd: - init - [ 36.605481] kmodloader: loading kernel modules from /etc/modules.d/* [ 36.732682] xt_time: kernel timezone is -0000 [ 36.847360] kmodloader: done loading kernel modules from /etc/modules.d/* [ 37.117008] urngd: v1.0.2 started. [ 37.390718] random: crng init done [ 37.394552] random: 1 urandom warning(s) missed due to ratelimiting [ 44.387493] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 52.393319] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 52.525157] in rtl838x_eth_stop [ 52.528932] rtl838x-eth 1b00a300.ethernet eth0: Link is Down [ 53.069080] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 53.076750] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 53.084254] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 53.091900] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 54.561082] Using MAC 000004bf6d22f5f8 [ 54.584670] RESETTING 8380, CPU_PORT 28 [ 54.789678] rtl838x-eth 1b00a300.ethernet eth0: configuring for fixed/internal link mode [ 54.798711] In rtl838x_mac_config, mode 1 [ 54.803700] In rtl838x_mac_config, mode 1 [ 54.808342] rtl838x-eth 1b00a300.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 54.856282] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 54.863431] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 54.871188] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 55.267268] do_page_fault(): sending SIGSEGV to realtek-poe for invalid write access to 004020cc [ 55.277228] epc = 77dcaff9 in libubox.so.20211120[77dc6000+17000] [ 55.284105] ra = 00401487 in realtek-poe[400000+3000] [ 55.305554] rtl83xx-switch switch@1b000000 lan1: configuring for phy/qsgmii link mode [ 55.325292] 8021q: adding VLAN 0 to HW filter on device lan1 [ 55.396860] switch: port 1(lan1) entered blocking state [ 55.402742] switch: port 1(lan1) entered disabled state [ 55.409769] device lan1 entered promiscuous mode [ 55.414955] device eth0 entered promiscuous mode [ 55.616658] rtl83xx-switch switch@1b000000 lan2: configuring for phy/qsgmii link mode [ 55.626339] 8021q: adding VLAN 0 to HW filter on device lan2 [ 55.656772] RTL8380 Link change: status: 1, ports 2 [ 55.716745] switch: port 2(lan2) entered blocking state [ 55.722637] switch: port 2(lan2) entered disabled state [ 55.729405] device lan2 entered promiscuous mode [ 55.986760] rtl83xx-switch switch@1b000000 lan3: configuring for phy/qsgmii link mode [ 55.996174] 8021q: adding VLAN 0 to HW filter on device lan3 [ 56.082442] switch: port 3(lan3) entered blocking state [ 56.088454] switch: port 3(lan3) entered disabled state [ 56.119909] device lan3 entered promiscuous mode [ 56.203996] rtl83xx-switch switch@1b000000 lan4: configuring for phy/qsgmii link mode [ 56.213712] 8021q: adding VLAN 0 to HW filter on device lan4 [ 56.275215] switch: port 4(lan4) entered blocking state [ 56.281231] switch: port 4(lan4) entered disabled state [ 56.304082] device lan4 entered promiscuous mode [ 56.314045] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 56.321767] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 56.394710] rtl83xx-switch switch@1b000000 lan5: configuring for phy/qsgmii link mode [ 56.404392] 8021q: adding VLAN 0 to HW filter on device lan5 [ 56.438530] switch: port 5(lan5) entered blocking state [ 56.444401] switch: port 5(lan5) entered disabled state [ 56.452700] device lan5 entered promiscuous mode [ 56.491162] rtl83xx-switch switch@1b000000 lan6: configuring for phy/qsgmii link mode [ 56.500692] 8021q: adding VLAN 0 to HW filter on device lan6 [ 56.536339] switch: port 6(lan6) entered blocking state [ 56.542218] switch: port 6(lan6) entered disabled state [ 56.550519] device lan6 entered promiscuous mode [ 56.584208] rtl83xx-switch switch@1b000000 lan7: configuring for phy/qsgmii link mode [ 56.593812] 8021q: adding VLAN 0 to HW filter on device lan7 [ 56.627265] switch: port 7(lan7) entered blocking state [ 56.633134] switch: port 7(lan7) entered disabled state [ 56.639912] device lan7 entered promiscuous mode [ 56.670861] rtl83xx-switch switch@1b000000 lan8: configuring for phy/qsgmii link mode [ 56.680394] 8021q: adding VLAN 0 to HW filter on device lan8 [ 56.714985] switch: port 8(lan8) entered blocking state [ 56.721026] switch: port 8(lan8) entered disabled state [ 56.727816] device lan8 entered promiscuous mode [ 56.755895] rtl83xx-switch switch@1b000000 lan9: configuring for phy/internal link mode [ 56.765784] 8021q: adding VLAN 0 to HW filter on device lan9 [ 56.801018] switch: port 9(lan9) entered blocking state [ 56.807024] switch: port 9(lan9) entered disabled state [ 56.813674] device lan9 entered promiscuous mode [ 56.842176] rtl83xx-switch switch@1b000000 lan10: configuring for phy/internal link mode [ 56.852146] 8021q: adding VLAN 0 to HW filter on device lan10 [ 56.885611] switch: port 10(lan10) entered blocking state [ 56.891848] switch: port 10(lan10) entered disabled state [ 56.898822] device lan10 entered promiscuous mode [ 56.927672] rtl83xx-switch switch@1b000000 lan11: configuring for phy/internal link mode [ 56.937336] 8021q: adding VLAN 0 to HW filter on device lan11 [ 56.970703] switch: port 11(lan11) entered blocking state [ 56.976906] switch: port 11(lan11) entered disabled state [ 56.983755] device lan11 entered promiscuous mode [ 57.010923] rtl83xx-switch switch@1b000000 lan12: configuring for phy/internal link mode [ 57.020706] 8021q: adding VLAN 0 to HW filter on device lan12 [ 57.055764] switch: port 12(lan12) entered blocking state [ 57.061993] switch: port 12(lan12) entered disabled state [ 57.068958] device lan12 entered promiscuous mode [ 57.101039] rtl83xx-switch switch@1b000000 lan13: configuring for phy/internal link mode [ 57.110682] 8021q: adding VLAN 0 to HW filter on device lan13 [ 57.145362] switch: port 13(lan13) entered blocking state [ 57.151592] switch: port 13(lan13) entered disabled state [ 57.158544] device lan13 entered promiscuous mode [ 57.183761] rtl83xx-switch switch@1b000000 lan14: configuring for phy/internal link mode [ 57.193677] 8021q: adding VLAN 0 to HW filter on device lan14 [ 57.227157] switch: port 14(lan14) entered blocking state [ 57.233223] switch: port 14(lan14) entered disabled state [ 57.240264] device lan14 entered promiscuous mode [ 57.264808] rtl83xx-switch switch@1b000000 lan15: configuring for phy/internal link mode [ 57.274825] 8021q: adding VLAN 0 to HW filter on device lan15 [ 57.309900] switch: port 15(lan15) entered blocking state [ 57.316098] switch: port 15(lan15) entered disabled state [ 57.322964] device lan15 entered promiscuous mode [ 57.350362] rtl83xx-switch switch@1b000000 lan16: configuring for phy/internal link mode [ 57.360380] 8021q: adding VLAN 0 to HW filter on device lan16 [ 57.393664] switch: port 16(lan16) entered blocking state [ 57.399891] switch: port 16(lan16) entered disabled state [ 57.406926] device lan16 entered promiscuous mode [ 57.433953] rtl83xx-switch switch@1b000000 lan17: configuring for phy/qsgmii link mode [ 57.443646] 8021q: adding VLAN 0 to HW filter on device lan17 [ 57.478323] switch: port 17(lan17) entered blocking state [ 57.484385] switch: port 17(lan17) entered disabled state [ 57.491377] device lan17 entered promiscuous mode [ 57.521978] rtl83xx-switch switch@1b000000 lan18: configuring for phy/qsgmii link mode [ 57.531751] 8021q: adding VLAN 0 to HW filter on device lan18 [ 57.566580] switch: port 18(lan18) entered blocking state [ 57.572654] switch: port 18(lan18) entered disabled state [ 57.579652] device lan18 entered promiscuous mode [ 57.606941] rtl83xx-switch switch@1b000000 lan19: configuring for phy/qsgmii link mode [ 57.616605] 8021q: adding VLAN 0 to HW filter on device lan19 [ 57.650098] switch: port 19(lan19) entered blocking state [ 57.656296] switch: port 19(lan19) entered disabled state [ 57.663130] device lan19 entered promiscuous mode [ 57.691230] rtl83xx-switch switch@1b000000 lan20: configuring for phy/qsgmii link mode [ 57.700733] 8021q: adding VLAN 0 to HW filter on device lan20 [ 57.734137] switch: port 20(lan20) entered blocking state [ 57.740359] switch: port 20(lan20) entered disabled state [ 57.747353] device lan20 entered promiscuous mode [ 57.778765] rtl83xx-switch switch@1b000000 lan21: configuring for phy/qsgmii link mode [ 57.788170] 8021q: adding VLAN 0 to HW filter on device lan21 [ 57.823991] switch: port 21(lan21) entered blocking state [ 57.830240] switch: port 21(lan21) entered disabled state [ 57.837241] device lan21 entered promiscuous mode [ 57.862403] rtl83xx-switch switch@1b000000 lan22: configuring for phy/qsgmii link mode [ 57.872233] 8021q: adding VLAN 0 to HW filter on device lan22 [ 57.909700] switch: port 22(lan22) entered blocking state [ 57.915769] switch: port 22(lan22) entered disabled state [ 57.922786] device lan22 entered promiscuous mode [ 57.950446] rtl83xx-switch switch@1b000000 lan23: configuring for phy/qsgmii link mode [ 57.960145] 8021q: adding VLAN 0 to HW filter on device lan23 [ 57.993775] switch: port 23(lan23) entered blocking state [ 58.000009] switch: port 23(lan23) entered disabled state [ 58.007045] device lan23 entered promiscuous mode [ 58.034369] rtl83xx-switch switch@1b000000 lan24: configuring for phy/qsgmii link mode [ 58.043983] 8021q: adding VLAN 0 to HW filter on device lan24 [ 58.078268] switch: port 24(lan24) entered blocking state [ 58.084334] switch: port 24(lan24) entered disabled state [ 58.091342] device lan24 entered promiscuous mode [ 58.120717] rtl83xx-switch switch@1b000000 lan25: configuring for inband/1000base-x link mode [ 58.130711] 8021q: adding VLAN 0 to HW filter on device lan25 [ 58.139744] switch: port 25(lan25) entered blocking state [ 58.145809] switch: port 25(lan25) entered disabled state [ 58.152831] device lan25 entered promiscuous mode [ 58.177567] rtl83xx-switch switch@1b000000 lan26: configuring for inband/1000base-x link mode [ 58.187557] 8021q: adding VLAN 0 to HW filter on device lan26 [ 58.199054] switch: port 26(lan26) entered blocking state [ 58.205123] switch: port 26(lan26) entered disabled state [ 58.212110] device lan26 entered promiscuous mode [ 58.233936] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 58.398485] RTL8380 Link change: status: 1, ports 2 [ 58.834009] rtl83xx-switch switch@1b000000 lan2: Link is Up - 1Gbps/Full - flow control rx/tx [ 58.879017] switch: port 2(lan2) entered blocking state [ 58.884894] switch: port 2(lan2) entered forwarding state [ 58.926505] IPv6: ADDRCONF(NETDEV_CHANGE): switch: link becomes ready [ 58.963676] IPv6: ADDRCONF(NETDEV_CHANGE): switch.1: link becomes ready [ 61.514894] Not offloading default route for now [ 61.845425] do_page_fault(): sending SIGSEGV to realtek-poe for invalid write access to 004020cc [ 61.855379] epc = 77dd0ff9 in libubox.so.20211120[77dcc000+17000] [ 61.862383] ra = 00401487 in realtek-poe[400000+3000] [ 68.392511] do_page_fault(): sending SIGSEGV to realtek-poe for invalid write access to 004020cc [ 68.402463] epc = 77df4ff9 in libubox.so.20211120[77df0000+17000] [ 68.409475] ra = 00401487 in realtek-poe[400000+3000] [ 74.825778] do_page_fault(): sending SIGSEGV to realtek-poe for invalid write access to 004020cc [ 74.835761] epc = 77db0ff9 in libubox.so.20211120[77dac000+17000] [ 74.842801] ra = 00401487 in realtek-poe[400000+3000] [ 81.262988] do_page_fault(): sending SIGSEGV to realtek-poe for invalid write access to 004020cc [ 81.272937] epc = 77db8ff9 in libubox.so.20211120[77db4000+17000] [ 81.279958] ra = 00401487 in realtek-poe[400000+3000] [ 87.694263] do_page_fault(): sending SIGSEGV to realtek-poe for invalid write access to 004020cc [ 87.704205] epc = 77de4ff9 in libubox.so.20211120[77de0000+17000] [ 87.711217] ra = 00401487 in realtek-poe[400000+3000] [ 239.524669] do_page_fault(): sending SIGSEGV to realtek-poe for invalid write access to 004020cc [ 239.534655] epc = 77d94ff9 in libubox.so.20211120[77d90000+17000] [ 239.541668] ra = 00401487 in realtek-poe[400000+3000] [ 245.959898] do_page_fault(): sending SIGSEGV to realtek-poe for invalid write access to 004020cc [ 245.969847] epc = 77d9aff9 in libubox.so.20211120[77d96000+17000] [ 245.976870] ra = 00401487 in realtek-poe[400000+3000] [ 252.392126] do_page_fault(): sending SIGSEGV to realtek-poe for invalid write access to 004020cc [ 252.402074] epc = 77db4ff9 in libubox.so.20211120[77db0000+17000] [ 252.409095] ra = 00401487 in realtek-poe[400000+3000] [ 258.823352] do_page_fault(): sending SIGSEGV to realtek-poe for invalid write access to 004020cc [ 258.833340] epc = 77d9aff9 in libubox.so.20211120[77d96000+17000] [ 258.840351] ra = 00401487 in realtek-poe[400000+3000] [ 265.262607] do_page_fault(): sending SIGSEGV to realtek-poe for invalid write access to 004020cc [ 265.272550] epc = 77d8eff9 in libubox.so.20211120[77d8a000+17000] [ 265.279580] ra = 00401487 in realtek-poe[400000+3000] [ 271.688827] do_page_fault(): sending SIGSEGV to realtek-poe for invalid write access to 004020cc [ 271.698776] epc = 77d7aff9 in libubox.so.20211120[77d76000+17000] [ 271.705655] ra = 00401487 in realtek-poe[400000+3000]