[ 0.000000] Linux version 5.10.103 (labby@lobon) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19053+1-921392e216) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 Sun Mar 6 19:33:17 2022 [ 0.000000] RTL838X model is 83826800 [ 0.000000] SoC Type: RTL8382 [ 0.000000] Kernel command line: console=ttyS0,115200 mem=64M quiet [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019070 (MIPS 4KEc) [ 0.000000] MIPS: machine is ZyXEL GS1900-24HP v1 [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Using appended Device Tree. [ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes. [ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] Normal zone: 144 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16384 pages, LIFO batch:3 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping off. Total pages: 16240 [ 0.000000] Kernel command line: console=ttyS0,115200 [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 55980K/65536K available (5609K kernel code, 613K rwdata, 1212K rodata, 1196K init, 203K bss, 9556K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] random: get_random_bytes called from start_kernel+0x31c/0x50c with crng_init=0 [ 0.000000] CPU frequency from device tree: 500MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns [ 0.000018] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns [ 0.008690] Calibrating delay loop... 498.89 BogoMIPS (lpj=2494464) [ 0.075562] pid_max: default: 32768 minimum: 301 [ 0.081055] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.089108] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.103284] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.119581] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.130497] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.138194] pinctrl core: initialized pinctrl subsystem [ 0.145347] NET: Registered protocol family 16 [ 0.315450] clocksource: Switched to clocksource MIPS [ 0.323807] NET: Registered protocol family 2 [ 0.329179] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.338468] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.347926] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.356497] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.364259] TCP: Hash tables configured (established 1024 bind 1024) [ 0.371903] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.379271] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.387564] NET: Registered protocol family 1 [ 0.412109] workingset: timestamp_bits=14 max_order=14 bucket_order=0 [ 0.428120] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.434504] jffs2: version 2.2 (NAND) (SUMMARY) (ZLIB) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.450560] pinctrl-single 1b001000.pinmux: 32 pins, size 4 [ 0.457485] pinctrl-single 1b00a000.pinmux: 32 pins, size 4 [ 0.464480] realtek_gpio_probe probing RTL GPIO [ 0.470866] Probing RTL8231 GPIOs [ 0.474482] rtl8231_init called, MDIO bus ID: 0 [ 0.479834] gpio-464 (poe_enable): hogged as output/high [ 0.587768] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.597064] printk: console [ttyS0] disabled [ 0.601854] 18002000.uart: ttyS0 at MMIO 0x18002000 (irq = 31, base_baud = 12500000) is a 16550A [ 0.611684] printk: console [ttyS0] enabled [ 0.621032] printk: bootconsole [early0] disabled [ 0.633081] 18002100.uart: ttyS1 at MMIO 0x18002100 (irq = 30, base_baud = 12500000) is a 16550A [ 1.319625] brd: module loaded [ 1.332714] spi-nor spi0.0: mx25l12805d (16384 Kbytes) [ 1.338735] 7 fixed-partitions partitions found on MTD device spi0.0 [ 1.345999] Creating 7 MTD partitions on "spi0.0": [ 1.351384] 0x000000000000-0x000000040000 : "u-boot" [ 1.362809] 0x000000040000-0x000000050000 : "u-boot-env" [ 1.371502] 0x000000050000-0x000000060000 : "u-boot-env2" [ 1.384937] 0x000000060000-0x000000160000 : "jffs" [ 1.392957] 0x000000160000-0x000000260000 : "jffs2" [ 1.405894] 0x000000260000-0x000000930000 : "firmware" [ 1.414523] 2 uimage-fw partitions found on MTD device firmware [ 1.421316] Creating 2 MTD partitions on "firmware": [ 1.427005] 0x000000000000-0x000000320000 : "kernel" [ 1.439851] 0x000000320000-0x0000006d0000 : "rootfs" [ 1.448001] mtd: device 7 (rootfs) set to be root filesystem [ 1.457029] 1 squashfs-split partitions found on MTD device rootfs [ 1.463987] 0x000000520000-0x0000006d0000 : "rootfs_data" [ 1.472673] 0x000000930000-0x000001000000 : "runtime2" [ 1.504768] Probing RTL838X eth device pdev: 82098c00, dev: 82098c10 [ 1.562470] Found SoC ID: 8382: RTL8382, family 8380 [ 1.568256] rtl8380_init_mac [ 1.571529] Using MAC 000004bf6d22f5f8 [ 1.668022] Realtek RTL8218B (internal) mdio-bus:08: Detected internal RTL8218B [ 1.676370] Firmware loaded. Size 1184, magic: 83808380 [ 2.595467] random: fast init done [ 4.215757] Phy on MAC 0: 1cc981 [ 4.229622] Realtek RTL8218B (external) mdio-bus:00: Detected external RTL8218B [ 4.237921] Firmware loaded. Size 1168, magic: 83808380 [ 4.385712] Realtek RTL8218B (external) mdio-bus:00: Detected chip revision 0002 [ 5.660661] mdio_bus mdio-bus: MDIO device at address 24 is missing. [ 5.668089] mdio_bus mdio-bus: MDIO device at address 26 is missing. [ 5.677232] i2c /dev entries driver [ 5.685429] NET: Registered protocol family 10 [ 5.715104] Segment Routing with IPv6 [ 5.719581] NET: Registered protocol family 17 [ 5.725403] 8021q: 802.1Q VLAN Support v1.8 [ 5.731399] i2c-gpio i2c-gpio-0: Slow GPIO pins might wreak havoc into I2C/SMBus bus timing [ 5.741409] i2c-gpio i2c-gpio-0: using lines 475 (SDA) and 476 (SCL) [ 5.749301] i2c-gpio i2c-gpio-1: Slow GPIO pins might wreak havoc into I2C/SMBus bus timing [ 5.759251] i2c-gpio i2c-gpio-1: using lines 481 (SDA) and 482 (SCL) [ 5.768273] sfp sfp-p25: Host maximum power 1.0W [ 5.775319] sfp sfp-p26: Host maximum power 1.0W [ 5.802942] Phy on MAC 0: 1cc981 [ 5.816911] Realtek RTL8218B (external) rtl838x slave mii-0:00: Detected external RTL8218B [ 5.826277] Firmware loaded. Size 1168, magic: 83808380 [ 5.975718] Realtek RTL8218B (external) rtl838x slave mii-0:00: Detected chip revision 0002 [ 7.228545] Realtek RTL8218B (internal) rtl838x slave mii-0:08: Detected internal RTL8218B [ 7.237917] Firmware loaded. Size 1184, magic: 83808380 [ 9.812260] rtl83xx_mdio_probe found port 8 [ 9.817122] rtl83xx_mdio_probe port 8 has phandle [ 9.822389] rtl83xx_mdio_probe port -1 has SDS [ 9.827467] rtl83xx_mdio_probe found port 9 [ 9.832153] rtl83xx_mdio_probe port 9 has phandle [ 9.837508] rtl83xx_mdio_probe port -1 has SDS [ 9.842493] rtl83xx_mdio_probe found port 10 [ 9.847396] rtl83xx_mdio_probe port 10 has phandle [ 9.852757] rtl83xx_mdio_probe port -1 has SDS [ 9.857835] rtl83xx_mdio_probe found port 11 [ 9.862618] rtl83xx_mdio_probe port 11 has phandle [ 9.868071] rtl83xx_mdio_probe port -1 has SDS [ 9.873055] rtl83xx_mdio_probe found port 12 [ 9.877931] rtl83xx_mdio_probe port 12 has phandle [ 9.883294] rtl83xx_mdio_probe port -1 has SDS [ 9.888367] rtl83xx_mdio_probe found port 13 [ 9.893154] rtl83xx_mdio_probe port 13 has phandle [ 9.898606] rtl83xx_mdio_probe port -1 has SDS [ 9.903591] rtl83xx_mdio_probe found port 14 [ 9.908493] rtl83xx_mdio_probe port 14 has phandle [ 9.913856] rtl83xx_mdio_probe port -1 has SDS [ 9.918933] rtl83xx_mdio_probe found port 15 [ 9.923716] rtl83xx_mdio_probe port 15 has phandle [ 9.929168] rtl83xx_mdio_probe port -1 has SDS [ 9.934153] rtl83xx_mdio_probe found port 28 [ 9.939033] rtl83xx_mdio_probe found port 0 [ 9.943717] rtl83xx_mdio_probe port 0 has phandle [ 9.949074] rtl83xx_mdio_probe port -1 has SDS [ 9.954062] rtl83xx_mdio_probe found port 1 [ 9.958837] rtl83xx_mdio_probe port 1 has phandle [ 9.964103] rtl83xx_mdio_probe port -1 has SDS [ 9.969178] rtl83xx_mdio_probe found port 2 [ 9.973868] rtl83xx_mdio_probe port 2 has phandle [ 9.979223] rtl83xx_mdio_probe port -1 has SDS [ 9.984210] rtl83xx_mdio_probe found port 3 [ 9.988988] rtl83xx_mdio_probe port 3 has phandle [ 9.994252] rtl83xx_mdio_probe port -1 has SDS [ 9.999327] rtl83xx_mdio_probe found port 4 [ 10.004017] rtl83xx_mdio_probe port 4 has phandle [ 10.009373] rtl83xx_mdio_probe port -1 has SDS [ 10.014368] rtl83xx_mdio_probe found port 5 [ 10.019169] rtl83xx_mdio_probe port 5 has phandle [ 10.024437] rtl83xx_mdio_probe port -1 has SDS [ 10.029521] rtl83xx_mdio_probe found port 6 [ 10.034209] rtl83xx_mdio_probe port 6 has phandle [ 10.039566] rtl83xx_mdio_probe port -1 has SDS [ 10.044561] rtl83xx_mdio_probe found port 7 [ 10.049339] rtl83xx_mdio_probe port 7 has phandle [ 10.054603] rtl83xx_mdio_probe port -1 has SDS [ 10.059677] rtl83xx_mdio_probe found port 16 [ 10.064464] rtl83xx_mdio_probe port 16 has phandle [ 10.069917] rtl83xx_mdio_probe port -1 has SDS [ 10.074911] rtl83xx_mdio_probe found port 17 [ 10.079785] rtl83xx_mdio_probe port 17 has phandle [ 10.085148] rtl83xx_mdio_probe port -1 has SDS [ 10.090222] rtl83xx_mdio_probe found port 18 [ 10.095009] rtl83xx_mdio_probe port 18 has phandle [ 10.100462] rtl83xx_mdio_probe port -1 has SDS [ 10.105550] rtl83xx_mdio_probe found port 19 [ 10.110339] rtl83xx_mdio_probe port 19 has phandle [ 10.115792] rtl83xx_mdio_probe port -1 has SDS [ 10.120786] rtl83xx_mdio_probe found port 20 [ 10.125684] rtl83xx_mdio_probe port 20 has phandle [ 10.131049] rtl83xx_mdio_probe port -1 has SDS [ 10.136128] rtl83xx_mdio_probe found port 21 [ 10.140918] rtl83xx_mdio_probe port 21 has phandle [ 10.146375] rtl83xx_mdio_probe port -1 has SDS [ 10.151367] rtl83xx_mdio_probe found port 22 [ 10.156242] rtl83xx_mdio_probe port 22 has phandle [ 10.161602] rtl83xx_mdio_probe port -1 has SDS [ 10.166679] rtl83xx_mdio_probe found port 23 [ 10.171463] rtl83xx_mdio_probe port 23 has phandle [ 10.176917] rtl83xx_mdio_probe port -1 has SDS [ 10.181910] rtl83xx_mdio_probe found port 24 [ 10.186795] rtl83xx-switch switch@1b000000: Port node 24 misses phy-handle [ 10.194484] rtl83xx_mdio_probe found port 26 [ 10.199367] rtl83xx-switch switch@1b000000: Port node 26 misses phy-handle [ 10.211717] In rtl83xx_vlan_setup [ 10.215587] UNKNOWN_MC_PMASK: 000000001fffffff [ 10.220569] VLAN profile 0: L2 learning: 1, UNKN L2MC FLD PMSK 511, UNKN IPMC FLD PMSK 511, UNKN IPv6MC FLD PMSK: 511 [ 11.305615] rtl83xx_enable_phy_polling: ffffff [ 12.346013] rtl83xx-switch switch@1b000000 lan1 (uninitialized): PHY [mdio-bus:00] driver [Realtek RTL8218B (external)] (irq=POLL) [ 12.361688] rtl83xx-switch switch@1b000000 lan2 (uninitialized): PHY [mdio-bus:01] driver [Realtek RTL8218B (external)] (irq=POLL) [ 12.377359] rtl83xx-switch switch@1b000000 lan3 (uninitialized): PHY [mdio-bus:02] driver [Realtek RTL8218B (external)] (irq=POLL) [ 12.393163] rtl83xx-switch switch@1b000000 lan4 (uninitialized): PHY [mdio-bus:03] driver [Realtek RTL8218B (external)] (irq=POLL) [ 12.408712] rtl83xx-switch switch@1b000000 lan5 (uninitialized): PHY [mdio-bus:04] driver [Realtek RTL8218B (external)] (irq=POLL) [ 12.424404] rtl83xx-switch switch@1b000000 lan6 (uninitialized): PHY [mdio-bus:05] driver [Realtek RTL8218B (external)] (irq=POLL) [ 12.440379] rtl83xx-switch switch@1b000000 lan7 (uninitialized): PHY [mdio-bus:06] driver [Realtek RTL8218B (external)] (irq=POLL) [ 12.456185] rtl83xx-switch switch@1b000000 lan8 (uninitialized): PHY [mdio-bus:07] driver [Realtek RTL8218B (external)] (irq=POLL) [ 12.471881] rtl83xx-switch switch@1b000000 lan9 (uninitialized): PHY [mdio-bus:08] driver [Realtek RTL8218B (internal)] (irq=POLL) [ 12.497728] rtl83xx-switch switch@1b000000 lan10 (uninitialized): PHY [mdio-bus:09] driver [Realtek RTL8218B (internal)] (irq=POLL) [ 12.523603] rtl83xx-switch switch@1b000000 lan11 (uninitialized): PHY [mdio-bus:0a] driver [Realtek RTL8218B (internal)] (irq=POLL) [ 12.550093] rtl83xx-switch switch@1b000000 lan12 (uninitialized): PHY [mdio-bus:0b] driver [Realtek RTL8218B (internal)] (irq=POLL) [ 12.576177] rtl83xx-switch switch@1b000000 lan13 (uninitialized): PHY [mdio-bus:0c] driver [Realtek RTL8218B (internal)] (irq=POLL) [ 12.602582] rtl83xx-switch switch@1b000000 lan14 (uninitialized): PHY [mdio-bus:0d] driver [Realtek RTL8218B (internal)] (irq=POLL) [ 12.628743] rtl83xx-switch switch@1b000000 lan15 (uninitialized): PHY [mdio-bus:0e] driver [Realtek RTL8218B (internal)] (irq=POLL) [ 12.654626] rtl83xx-switch switch@1b000000 lan16 (uninitialized): PHY [mdio-bus:0f] driver [Realtek RTL8218B (internal)] (irq=POLL) [ 12.680802] rtl83xx-switch switch@1b000000 lan17 (uninitialized): PHY [mdio-bus:10] driver [REALTEK RTL8218D] (irq=POLL) [ 12.705517] rtl83xx-switch switch@1b000000 lan18 (uninitialized): PHY [mdio-bus:11] driver [REALTEK RTL8218D] (irq=POLL) [ 12.730523] rtl83xx-switch switch@1b000000 lan19 (uninitialized): PHY [mdio-bus:12] driver [REALTEK RTL8218D] (irq=POLL) [ 12.755982] rtl83xx-switch switch@1b000000 lan20 (uninitialized): PHY [mdio-bus:13] driver [REALTEK RTL8218D] (irq=POLL) [ 12.781098] rtl83xx-switch switch@1b000000 lan21 (uninitialized): PHY [mdio-bus:14] driver [REALTEK RTL8218D] (irq=POLL) [ 12.806001] rtl83xx-switch switch@1b000000 lan22 (uninitialized): PHY [mdio-bus:15] driver [REALTEK RTL8218D] (irq=POLL) [ 12.831036] rtl83xx-switch switch@1b000000 lan23 (uninitialized): PHY [mdio-bus:16] driver [REALTEK RTL8218D] (irq=POLL) [ 12.856170] rtl83xx-switch switch@1b000000 lan24 (uninitialized): PHY [mdio-bus:17] driver [REALTEK RTL8218D] (irq=POLL) [ 12.874806] rtl83xx-switch switch@1b000000: configuring for fixed/internal link mode [ 12.884335] DSA: tree 0 setup [ 12.887915] LINK state irq: 20 [ 12.891434] In rtl83xx_setup_qos [ 12.895046] Setting up RTL838X QoS [ 12.898955] RTL838X_PRI_SEL_TBL_CTRL(i): 00033112 [ 12.904215] Current Intprio2queue setting: 00000000 [ 12.909755] QM_PKT2CPU_INTPRI_MAP: 00fac688 [ 12.914600] rtl838x_dbgfs_init called [ 12.985304] rtl83xx-switch switch@1b000000: Link is Up - 1Gbps/Full - flow control off [ 13.004867] VFS: Mounted root (squashfs filesystem) readonly on device 31:7. [ 13.026610] Freeing unused kernel memory: 1196K [ 13.031697] This architecture does not have kernel memory protection. [ 13.039035] Run /sbin/init as init process [ 13.043624] with arguments: [ 13.047037] /sbin/init [ 13.050074] with environment: [ 13.053575] HOME=/ [ 13.056307] TERM=linux [ 13.059515] rtl83xx_fib_event_work_do: FIB4 default rule failed [ 13.883313] init: Console is alive [ 13.888278] init: - watchdog - [ 14.119515] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 14.234314] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 14.253530] init: - preinit - [ 15.809451] random: jshn: uninitialized urandom read (4 bytes read) [ 15.964119] random: jshn: uninitialized urandom read (4 bytes read) [ 17.619151] random: jshn: uninitialized urandom read (4 bytes read) [ 17.723214] random: jshn: uninitialized urandom read (4 bytes read) [ 18.107206] random: jshn: uninitialized urandom read (4 bytes read) [ 18.880108] RESETTING 8380, CPU_PORT 28 [ 19.085118] rtl838x-eth 1b00a300.ethernet eth0: configuring for fixed/internal link mode [ 19.094188] In rtl838x_mac_config, mode 1 [ 19.102748] rtl83xx-switch switch@1b000000 lan1: configuring for phy/qsgmii link mode [ 19.112042] 8021q: adding VLAN 0 to HW filter on device lan1 [ 19.119067] In rtl838x_mac_config, mode 1 [ 19.123614] rtl838x-eth 1b00a300.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 19.175658] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 19.182814] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 19.190529] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 19.322547] rtl83xx_fib_event_work_do: FIB4 failed [ 19.335701] rtl83xx_fib_event_work_do: FIB4 failed [ 19.341092] rtl83xx_fib_event_work_do: FIB4 failed [ 19.355667] rtl83xx_fib_event_work_do: FIB4 failed [ 19.441828] random: procd: uninitialized urandom read (4 bytes read) [ 20.745620] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 23.905955] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000 [ 23.914061] jffs2_build_filesystem(): unlocking the mtd device... [ 23.914182] done. [ 23.923343] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 30.852176] done. [ 30.862972] jffs2: notice: (1316) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 30.883738] mount_root: overlay filesystem has not been fully initialized yet [ 30.897126] mount_root: switching to jffs2 overlay [ 30.908073] overlayfs: upper fs does not support tmpfile. [ 31.707630] urandom-seed: Seed file not found (/etc/urandom.seed) [ 31.955172] rtl83xx_fib4_del: no such gateway: 0.0.0.0 [ 31.964545] rtl83xx_fib4_del: no such gateway: 0.0.0.0 [ 31.985780] rtl83xx_fib4_del: no such gateway: 0.0.0.0 [ 31.991563] rtl83xx_fib4_del: no such gateway: 0.0.0.0 [ 32.032724] procd: - early - [ 32.036878] procd: - watchdog - [ 34.731630] procd: - watchdog - [ 34.736593] procd: - ubus - [ 34.861350] random: ubusd: uninitialized urandom read (4 bytes read) [ 34.871901] random: ubusd: uninitialized urandom read (4 bytes read) [ 34.880304] random: ubusd: uninitialized urandom read (4 bytes read) [ 34.897699] procd: - init - [ 36.580120] kmodloader: loading kernel modules from /etc/modules.d/* [ 36.697419] xt_time: kernel timezone is -0000 [ 36.816953] kmodloader: done loading kernel modules from /etc/modules.d/* [ 37.100700] urngd: v1.0.2 started. [ 37.376711] random: crng init done [ 37.380541] random: 1 urandom warning(s) missed due to ratelimiting [ 44.308972] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 52.279508] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 52.380734] in rtl838x_eth_stop [ 52.384404] rtl838x-eth 1b00a300.ethernet eth0: Link is Down [ 52.938394] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 52.946031] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 52.953540] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 52.961180] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 54.373735] Using MAC 000004bf6d22f5f8 [ 54.412277] RESETTING 8380, CPU_PORT 28 [ 54.617285] rtl838x-eth 1b00a300.ethernet eth0: configuring for fixed/internal link mode [ 54.626328] In rtl838x_mac_config, mode 1 [ 54.631311] In rtl838x_mac_config, mode 1 [ 54.635958] rtl838x-eth 1b00a300.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 54.676682] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 54.683832] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 54.691592] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 55.157433] rtl83xx-switch switch@1b000000 lan1: configuring for phy/qsgmii link mode [ 55.177467] 8021q: adding VLAN 0 to HW filter on device lan1 [ 55.244162] switch: port 1(lan1) entered blocking state [ 55.250221] switch: port 1(lan1) entered disabled state [ 55.257205] device lan1 entered promiscuous mode [ 55.262388] device eth0 entered promiscuous mode [ 55.275384] do_page_fault(): sending SIGSEGV to realtek-poe for invalid write access to 004020cc [ 55.285373] epc = 77d4eff9 in libubox.so.20211120[77d4a000+17000] [ 55.292355] ra = 00401487 in realtek-poe[400000+3000] [ 55.496100] rtl83xx-switch switch@1b000000 lan2: configuring for phy/qsgmii link mode [ 55.505616] 8021q: adding VLAN 0 to HW filter on device lan2 [ 55.535422] RTL8380 Link change: status: 1, ports 2 [ 55.596261] switch: port 2(lan2) entered blocking state [ 55.602159] switch: port 2(lan2) entered disabled state [ 55.608921] device lan2 entered promiscuous mode [ 55.848064] rtl83xx-switch switch@1b000000 lan3: configuring for phy/qsgmii link mode [ 55.857527] 8021q: adding VLAN 0 to HW filter on device lan3 [ 55.950515] switch: port 3(lan3) entered blocking state [ 55.956521] switch: port 3(lan3) entered disabled state [ 55.995814] device lan3 entered promiscuous mode [ 56.062796] rtl83xx-switch switch@1b000000 lan4: configuring for phy/qsgmii link mode [ 56.072128] 8021q: adding VLAN 0 to HW filter on device lan4 [ 56.118370] switch: port 4(lan4) entered blocking state [ 56.124253] switch: port 4(lan4) entered disabled state [ 56.165904] device lan4 entered promiscuous mode [ 56.226270] rtl83xx-switch switch@1b000000 lan5: configuring for phy/qsgmii link mode [ 56.235842] 8021q: adding VLAN 0 to HW filter on device lan5 [ 56.289575] switch: port 5(lan5) entered blocking state [ 56.295586] switch: port 5(lan5) entered disabled state [ 56.320471] device lan5 entered promiscuous mode [ 56.345733] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 56.353313] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 56.411570] rtl83xx-switch switch@1b000000 lan6: configuring for phy/qsgmii link mode [ 56.421227] 8021q: adding VLAN 0 to HW filter on device lan6 [ 56.455100] switch: port 6(lan6) entered blocking state [ 56.461107] switch: port 6(lan6) entered disabled state [ 56.469541] device lan6 entered promiscuous mode [ 56.503311] rtl83xx-switch switch@1b000000 lan7: configuring for phy/qsgmii link mode [ 56.512625] 8021q: adding VLAN 0 to HW filter on device lan7 [ 56.547294] switch: port 7(lan7) entered blocking state [ 56.553168] switch: port 7(lan7) entered disabled state [ 56.559931] device lan7 entered promiscuous mode [ 56.591602] rtl83xx-switch switch@1b000000 lan8: configuring for phy/qsgmii link mode [ 56.600901] 8021q: adding VLAN 0 to HW filter on device lan8 [ 56.636085] switch: port 8(lan8) entered blocking state [ 56.641965] switch: port 8(lan8) entered disabled state [ 56.648739] device lan8 entered promiscuous mode [ 56.676794] rtl83xx-switch switch@1b000000 lan9: configuring for phy/internal link mode [ 56.686315] 8021q: adding VLAN 0 to HW filter on device lan9 [ 56.719401] switch: port 9(lan9) entered blocking state [ 56.725279] switch: port 9(lan9) entered disabled state [ 56.732058] device lan9 entered promiscuous mode [ 56.760533] rtl83xx-switch switch@1b000000 lan10: configuring for phy/internal link mode [ 56.770235] 8021q: adding VLAN 0 to HW filter on device lan10 [ 56.803578] switch: port 10(lan10) entered blocking state [ 56.809811] switch: port 10(lan10) entered disabled state [ 56.816755] device lan10 entered promiscuous mode [ 56.845377] rtl83xx-switch switch@1b000000 lan11: configuring for phy/internal link mode [ 56.855296] 8021q: adding VLAN 0 to HW filter on device lan11 [ 56.890368] switch: port 11(lan11) entered blocking state [ 56.896577] switch: port 11(lan11) entered disabled state [ 56.903428] device lan11 entered promiscuous mode [ 56.932693] rtl83xx-switch switch@1b000000 lan12: configuring for phy/internal link mode [ 56.942533] 8021q: adding VLAN 0 to HW filter on device lan12 [ 56.977196] switch: port 12(lan12) entered blocking state [ 56.983260] switch: port 12(lan12) entered disabled state [ 56.990300] device lan12 entered promiscuous mode [ 57.020131] rtl83xx-switch switch@1b000000 lan13: configuring for phy/internal link mode [ 57.029944] 8021q: adding VLAN 0 to HW filter on device lan13 [ 57.063487] switch: port 13(lan13) entered blocking state [ 57.069716] switch: port 13(lan13) entered disabled state [ 57.076647] device lan13 entered promiscuous mode [ 57.101839] rtl83xx-switch switch@1b000000 lan14: configuring for phy/internal link mode [ 57.111634] 8021q: adding VLAN 0 to HW filter on device lan14 [ 57.146440] switch: port 14(lan14) entered blocking state [ 57.152510] switch: port 14(lan14) entered disabled state [ 57.159487] device lan14 entered promiscuous mode [ 57.186194] rtl83xx-switch switch@1b000000 lan15: configuring for phy/internal link mode [ 57.196126] 8021q: adding VLAN 0 to HW filter on device lan15 [ 57.229679] switch: port 15(lan15) entered blocking state [ 57.235883] switch: port 15(lan15) entered disabled state [ 57.242725] device lan15 entered promiscuous mode [ 57.268148] rtl83xx-switch switch@1b000000 lan16: configuring for phy/internal link mode [ 57.277814] 8021q: adding VLAN 0 to HW filter on device lan16 [ 57.312074] switch: port 16(lan16) entered blocking state [ 57.318284] switch: port 16(lan16) entered disabled state [ 57.325153] device lan16 entered promiscuous mode [ 57.354175] rtl83xx-switch switch@1b000000 lan17: configuring for phy/qsgmii link mode [ 57.363884] 8021q: adding VLAN 0 to HW filter on device lan17 [ 57.398980] switch: port 17(lan17) entered blocking state [ 57.405044] switch: port 17(lan17) entered disabled state [ 57.412022] device lan17 entered promiscuous mode [ 57.440222] rtl83xx-switch switch@1b000000 lan18: configuring for phy/qsgmii link mode [ 57.449968] 8021q: adding VLAN 0 to HW filter on device lan18 [ 57.483176] switch: port 18(lan18) entered blocking state [ 57.489403] switch: port 18(lan18) entered disabled state [ 57.496359] device lan18 entered promiscuous mode [ 57.523821] rtl83xx-switch switch@1b000000 lan19: configuring for phy/qsgmii link mode [ 57.533404] 8021q: adding VLAN 0 to HW filter on device lan19 [ 57.568067] switch: port 19(lan19) entered blocking state [ 57.574135] switch: port 19(lan19) entered disabled state [ 57.581089] device lan19 entered promiscuous mode [ 57.608683] rtl83xx-switch switch@1b000000 lan20: configuring for phy/qsgmii link mode [ 57.618492] 8021q: adding VLAN 0 to HW filter on device lan20 [ 57.653617] switch: port 20(lan20) entered blocking state [ 57.659836] switch: port 20(lan20) entered disabled state [ 57.666783] device lan20 entered promiscuous mode [ 57.698425] rtl83xx-switch switch@1b000000 lan21: configuring for phy/qsgmii link mode [ 57.708251] 8021q: adding VLAN 0 to HW filter on device lan21 [ 57.745391] switch: port 21(lan21) entered blocking state [ 57.751642] switch: port 21(lan21) entered disabled state [ 57.758623] device lan21 entered promiscuous mode [ 57.783761] rtl83xx-switch switch@1b000000 lan22: configuring for phy/qsgmii link mode [ 57.793295] 8021q: adding VLAN 0 to HW filter on device lan22 [ 57.829174] switch: port 22(lan22) entered blocking state [ 57.835240] switch: port 22(lan22) entered disabled state [ 57.842236] device lan22 entered promiscuous mode [ 57.869655] rtl83xx-switch switch@1b000000 lan23: configuring for phy/qsgmii link mode [ 57.879184] 8021q: adding VLAN 0 to HW filter on device lan23 [ 57.912596] switch: port 23(lan23) entered blocking state [ 57.918827] switch: port 23(lan23) entered disabled state [ 57.925821] device lan23 entered promiscuous mode [ 57.955830] rtl83xx-switch switch@1b000000 lan24: configuring for phy/qsgmii link mode [ 57.965162] 8021q: adding VLAN 0 to HW filter on device lan24 [ 57.999839] switch: port 24(lan24) entered blocking state [ 58.006040] switch: port 24(lan24) entered disabled state [ 58.012888] device lan24 entered promiscuous mode [ 58.039983] rtl83xx-switch switch@1b000000 lan25: configuring for inband/1000base-x link mode [ 58.049970] 8021q: adding VLAN 0 to HW filter on device lan25 [ 58.058918] switch: port 25(lan25) entered blocking state [ 58.064981] switch: port 25(lan25) entered disabled state [ 58.072009] device lan25 entered promiscuous mode [ 58.096679] rtl83xx-switch switch@1b000000 lan26: configuring for inband/1000base-x link mode [ 58.106664] 8021q: adding VLAN 0 to HW filter on device lan26 [ 58.118321] switch: port 26(lan26) entered blocking state [ 58.124391] switch: port 26(lan26) entered disabled state [ 58.131371] device lan26 entered promiscuous mode [ 58.144647] RTL8380 Link change: status: 1, ports 2 [ 58.159612] rtl83xx_fib_event: FIB_RULE ADD/DELL for IPv6 not supported [ 58.753368] rtl83xx-switch switch@1b000000 lan2: Link is Up - 1Gbps/Full - flow control rx/tx [ 58.802793] switch: port 2(lan2) entered blocking state [ 58.808807] switch: port 2(lan2) entered forwarding state [ 58.847704] IPv6: ADDRCONF(NETDEV_CHANGE): switch: link becomes ready [ 58.894444] IPv6: ADDRCONF(NETDEV_CHANGE): switch.1: link becomes ready [ 61.419129] Not offloading default route for now [ 61.776748] do_page_fault(): sending SIGSEGV to realtek-poe for invalid write access to 004020cc [ 61.786743] epc = 77e22ff9 in libubox.so.20211120[77e1e000+17000] [ 61.793613] ra = 00401487 in realtek-poe[400000+3000] [ 68.314918] do_page_fault(): sending SIGSEGV to realtek-poe for invalid write access to 004020cc [ 68.325097] epc = 77de2ff9 in libubox.so.20211120[77dde000+17000] [ 68.332120] ra = 00401487 in realtek-poe[400000+3000]